The post SSC JE Previous Question Paper 2018 Shift 7 (Civil Engineering) appeared first on NewtonDesk.

]]>**Q1:-** Air permeability method is used in which of the following test of cement?

**Options:
**

**Q2:-** The main purpose of the soundness test of the cement is to determine the____.

**Options:
**

**Q3:-** What is the target mean strength (N/mm^{2}) of the M30 grade concrete, if the standard deviation is 5.0?

**Options:
**

**Q4:-** Which of the following method is used to make the timber ﬁre resistance?

**Options:
**

**Q5:-** In which of the following process, plug mill is used?

**Options:
**

**Q6:-** According to the IS speciﬁcations, initial setting time of the ordinary Portland cement should be____.

**Options:
**

**Q7:-** Which of the following is the main reason to provide frog in the bricks?

**Options:
**

**Q8:-** Which of the following is used as the vehicle in the enamel paints?

**Options:
**

**Q9:-** If one cement bag has 0.035m^{2} volume of cement, the number of bags required for one tonne of cement is______.

**Options:
**

**Q10:-** Which of the following is fused together to prepare the high alumina cement?

**Options:
**

**Q11:-** Accuracy in the measurement of the volume in cubic meter should be near to_____.

**Options:
**

**Q12:-** Deduction for total length of the central line at the corner where two walls meet is_____.

**Options:
**

**Q13:-** Which of the following is estimated by using a bar bending schedule?

**Options:
**

**Q14:-** Which of the following is measured in square meter?

**Options:
**

**Q15:-** Which of the following statements are the CORRECT for estimation of plastering?

**1)** For opening up to 0.5 square meters, no deduction is made.

**2)** For opening exceeding 0.5 square meters and up to 3 square meters, deduction is made for one face.

**3)** For opening up to 3 square meters, deduction is made for both faces.

**4)** For ends of beams, no deduction is made.

**Options:
**

**Q16:-** Chowkhat or frame of the door is measured in______.

**Options:
**

**Q17:-** Calculate the preliminary estimate for a building having a total carpet area of 500 square meters. Extra provision as 10% of the carpet area is provided for walls and verandah. The plinth area rate is Rs. 1,200 per square meter.

**Options:
**

**Q18:-** Calculate the volume of earth work for an embankment of length L and width B. The mean depth of the embankment is D and side slope is S : 1.Using mid- sectional area method.

**Options:
**

**Q19:-** Calculate the quantity of the sand required for 8 cubic meter brick work with cement mortar (1 : 3).

**Options:
**

**Q20:-** Calculate the capitalized value of a building having annual rent of Rs. 20,000 and highest rate of interest is 5%.

**Options:
**

**Q21:-** Plumb bob lines at two different places in plane surveying are_____.

**Options:
**

**Q22:-** A curve whose radius varies from inﬁnity to a certain value is called______.

**Options:
**

**Q23:-** What is the representative fraction for a scale of 10 cm = 20 km?

**Options:
**

**Q24:-** The line which is used to collect the details of the objects in an area is called_____.

**Options:
**

**Q25:-** Calculate true bearing of a line, if magnetic bearing of the line is S 60^{o} E and magnetic declination is 5^{o} eastward.

**Options:
**

**SSC Junior Engineer (JE) All Previous Papers (NewtonDesk.com)**

**Q26:-** Calculate the total correction (m) required, if a line measured using 20 m chain is 2380 m. Actual length of the chain is 20.2 m.

**Options:
**

**Q27:-** The least count of a theodolite is_____.

**Options:
**

**Q28:-** Calculate the corrected staff reading at point A, if the staff reading is taken from an instrument which is set at a distance of 1.5 km from the point A 3.46 m.

**Options:
**

**Q29:-** Calculate the intersect angle (degree) for the anallactic telescope.

**Options:
**

**Q30:-** Which of the following statements are CORRECT for contour map?

**1)** Parallel contour shows uniform slope.

**2)** Very closed contour shows steep slope.

**3)** Very closed contour shows ﬂat area.

**4)** Two contours at different elevation cut at right angle.

**Options:
**

**Q31:-** What is the terminal velocity (m/s) for a 4 g particle which is falling in the water with projected area of 5 sq. cm? The coefﬁcient of drag is given as 0.47.

**Options:
**

**Q32:-** The coefﬁcient of curvature for well graded soil lies between______.

**Options:
**

**Q33:-** The coefﬁcient of uniformity for well graded sand must be greater than______.

**Options:
**

**Q34:-** Casagrande’s apparatus is used to determine_____.

**Options:
**

**Q35:-** On increasing temperature, the viscosity of gas_____.

**Options:
**

**Q36:-** If the 90% volume of iceberg is immersed in the water and only 10% volume is above the water surface. What is the density of the iceberg, the density of sea water is given as 1025 kg/m^{3}?

**Options:
**

**Q37:-** The head developed by the centrifugal pump is 40 m while operating at the speed of 750 rpm. If the rated capacity is given as 50 cumec, what is the speciﬁc speed of centrifugal pump?

**Options:
**

**Q38:-** Surface tension for an ideal ﬂuid is_____.

**Options:
**

**Q39:-** Which of the following is not true about density of the gases?

**Options:
**

**Q40:-** The stable equilibrium is achieved in the ﬂoating body when_____.

**Options:
**

**Q41:-** What is the value of friction factor, if the diameter of pipe is 50 cm and roughness height is 0.25 cm?

**Options:
**

**Q42:**– What is the head loss in pipe due to friction over the length of 30 km, if the diameter of pipe is 80 cm and velocity of ﬂow is 30 cm/s? Take friction factor 0.032.

**Options:
**

**Q43:-** The range of Froud number for the weak jump is_____.

**Options:
**

**Q44:-** What is the velocity (m/s) with which elementary wave can travel upstream, if the velocity of ﬂow is 2 m/s and depth of ﬂow in channel is 1 m?

**Options:
**

**Q45:-** Which one is the best method of reclamation of the alkaline soil?

**Options:
**

**Q46:-** The intensity of the rainfall for successive 1 hours period of a 6 hours storm are 2, 6, 8, 9, 7 and 3 cm/hr. The runoff is 4 cm/hr. Calculate the Ф-index (cm/hr).

**Options:
**

**Q47:-** The intermediate sight distance is equal to______.

**Options:
**

**Q48:-** Calculate the equivalent radius of the resisting section of 20 cm thick slab, if the ratio of the radius of wheel load distribution to the thickness of the slab is 0.5.

**Options:
**

**Q49:-** Which of the following is responsible for the corrosion of concrete sewers?

**Options:
**

**Q50:–** Which of the following is responsible for the depletion of ozone layer in the upper atmosphere?

**Options:
**

**SSC Junior Engineer (JE) All Previous Papers (NewtonDesk.com)**

**Q51:-** Live loads, with time can vary in:-

**Options:
**

**Q52:-** Impact load results from which type of effects of loads applied?

**Options:
**

**Q53:-** Which type of drainage system will collect the rainwater?

**Options:
**

**Q54:-** Moment at a hinge will be:-

**Options:
**

**Q55:-** For the validity of principle of superposition, materials should behave in which manner?

**Options:
**

**Q56:-** If 4 reactions are acting on a beam, then the system is:-

**Options:
**

**Q57:-** Which of the following statements is true?

**1.** If a truss consists of a non-triangular element, then it will essentially be unstable.

**2.** In the above cases, instability is the most probable occurrence, but there are a lot of examples which are unstable.

**Options:
**

**Q58:-** Which of the following statements is true?

**1.** A roller is provided at end of a bridge truss to allow thermal expansion.

**2.** A roller provides freedom of deformation in horizontal plane in case of thermal expansion.

**Options:
**

**Q59:-** Trusses and frames are different as:-

**Options:
**

**Q60:-** Given that J is no. of joints. B and R are no. of members and no. of reactions. If B = 5, R = 4 and J = 4, then the truss is:-

**Options:
**

**Q61:-** What is the ideal water-cement ratio to be used while hand mixing?

**Options:
**

**Q62:-** As water cement ratio increases, ______also increases.

**Options:
**

**Q63:-** Ready mix plant and central mix plant differ in:

**Options:
**

**Q64:-** Compacting of concrete is done to:

**Options:
**

**Q65:-** Which of the following statements is true?

**1. **A gap of 0.3m is to be maintained between cement bag and wall, while storing cement.

**2. **A gap 100 cm is to be maintained between cement bag and wall, while storing cement.

**Options:
**

**Q66:-** Which of the following statements is true?

**1. **Impermeability is a property of fresh concrete.

**2. **Impermeability is a not property of fresh concrete.

**3. **Impermeability is nothing to with concrete at all.

**Options:
**

**Q67:-** M15 concrete is used for:

**Options:
**

**Q68:-** Tensile strength of concrete is found out using:

**Options:
**

**Q69:-** A slump of 50-100mm can be used for:

**Options:
**

**Q70:-** Before plastering, the surface has to be:

**Options:
**

**Q71:-** Wood surface requires______ coats of plastering.

**Options:
**

**Q72:-** For the construction of the retaining structures, the type of concrete mix to be used is

**1.** 1:3:6

**2. **1:2:4

**3. **1:1.5:3

**4.** 1:1:2

**Options:
**

**Q73:-** For preparing ordinary concrete, what is the quantity of water used?

**Options:
**

**Q74:-** If the various concrete ingredients i.e. cement, sand, aggregates are in the ratio of 1:3:6, the grade of concrete is

**Options:
**

**Q75:-** For which of the following is an ideal warehouse is provided?

**Options:
**

**SSC Junior Engineer (JE) All Previous Papers (NewtonDesk.com)**

**Q76:-** If the internal dimensions of a ware house are 15 m x 5.6 m and the maximum height of piles is 2.70 m, then what is the maximum number of bags to be stored in two piles?

**Options:
**

**Q77:-** Which of the following statements is true?

**Options:
**

**Q78:-** For concreting tunnel linings, transportation of concrete is done by which of the following?

**Options:
**

**Q79:-** ______is used to construct very thin, hard and strong surface

**Options:
**

**Q80:-** How many methods of ferro cementing are there?

**Options:
**

**Q81:–** The effective width of a column strip of a ﬂat slab that is taken into consideration?

**Options:
**

**Q82:-** If W is the Uniformly distributed load on a circular slab of radius R fixed at its ends, the maximum positive radial R fixed at its ends, the maximum positive radial moment at its center is

**A)** 3WR^{2} / 16

**B)** 2WR^{2} / 16

**C)** WR^{2} / 16

**Options:
**

**Q83:-** For initial estimate for a beam design, the width is assumed

**Options:
**

**Q84:-** The thickness of the topping of a ribbed slab, varies between

**Options:
**

**Q85:-** For a ribbed slab

**Options:
**

**Q86:-** Which of the following statements is true?

**Options:
**

**Q87:-** According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges is kept less than

**Options:
**

**Q88:-** If the diameter of longitudinal bars of a square column is 16 mm, the diameter of lateral ties should not be less than

**Options:
**

**Q89:-** Maximum strain theory for the failure of a material at the elastic limit is known as

**Options:
**

**Q90:-** Gradually applied static loads do not change with time their

**Options:
**

**Q91:-** The thickness of slabs and beams must be measured to the nearest:-

**Options:
**

**Q92:-** A composite beam is composed of two equal strips one of brass and other of steel. If the temperature is raised

**Options:
**

**Q93:-** A linear force-deformation relation is obtained in materials

**Options:
**

**Q94:-** In a structure, why are the cables and wires are generally used?

**Options:
**

**Q95:-** The ability of a material to absorb energy till the elastic limit is known as

**1)** Ductility

**2)** Malleability

**3)** Elasticity

**4)** None of these

**Answer:** None of these

**Q96:-** If a material has identical properties in all directions, It is said to be

**Options:
**

**Q97:-** If all the dimensions of a prismatic bar are double, then the maximum stress produced in it under its weight will

**Options:
**

**Q98:-** The ratio of the length of the column to the minimum radius of gyration of the cross sectional area of the column is known as

**Options:
**

**Q99:-** In a built-up section carrying tensile force, the ﬂanges of two channels are turned outward

**Options:
**

**Q100:-** A tension member, if subjected to possible reversal of stress due to wind, the slenderness ratio of the member should not exceed

**Options:
**

**SSC Junior Engineer All Previous Papers**

The post SSC JE Previous Question Paper 2018 Shift 7 (Civil Engineering) appeared first on NewtonDesk.

]]>